A – Fixed Advanced

The cranked dipper arm, brings the cutting head in line with the operator.
This improves the visibility of the fly head and reduces the need for the operator to look over his shoulder, allowing more attention to be given to what is happening in the front of the tractor.

APS

Enables the operator to adjust the position of the cutting head to improve visibility. When verge mowing the arm can be pushed forward so the cutting attachment can be seen through the tractor door. When hedge cutting the attachment can be positioned in-line with the operator for improved visibility.All thanks by of the
Advanced Parallelogram System (APS).

ARC

The ARC system allows the operator to bypass obstacles such as vines, hedges and any constraint which does not allow the passage of the Flail Hedger Mower along the scything area. The first curved arm (ARC) and raised, allowing extreme compactness, stability and ample free space under the arms.

MT

Machine with side shift

Parallelogram System

The parallelogram system enables the operator to adjust the reach of the machines arms, without the need to continuously adjust the ‘lift’ service in order to compensate for the change in head pivot height – as would be the case with conventional arm geometry. This arm geometry enables the cutting attachment to cut tight to the
tractor at any height within the cutting range, ideal for cutting hedges at all heights in narrow lanes and other situations where space is at a premium. The high positioning of the first arm also gives excellent over fence clearance and down bank reach.

SI System

The system to sustenance Electro-proportional (SI System) provides a speed control scything grass more higher, increasing the efficiency and safety of the Flail Hedger Mower. The cutting head floats on the ground automatically, allowing greater cutting speed in relation to the position of the cutting head from the tractor. SI System
ensures a precise and responsive flotation of the cutting head, increasing the speed and efficiency of use, reducing operator fatigue.

SSAB – STRENX

STRONGER AND LIGHTER. Strenx performance steel has great potential to make your products stronger, lighter, safer, more competitive and more sustainable. “Think thinner – and get stronger” The materials of our machines are supplied by the Swedish company SSAB

Telescopic arm

The Telescopic dipper arms increase the extension of second arm (dependent on model). This results in a machine that has compact arm geometry for close-in cutting plus also has the reach abilities when needed.

X – Rotation

The rotation back of the arms upwards and enables to rotate from 90° to 110° (in relations of the machines type) backwards from working position. The rotation back not only enables the arms to fold in to a compact transport position, it also gives the operator the ability to cut behind them, ideal for cutting out corners in hedge rows.

EPP – EPG

Moving with “Load Sensing” compensated proportional electric distributor.
The characteristic of this system is that it maintains a constant oil flow in every section, independently of changes of the load, and allows more than one movement simultaneously and independently of each other, without interference.

Joystick MJ, BJ e VSC

MJ – Single lever and compact console. Reactive joystick that is not only functional but also provides further axis control of the brushcutter through lever rotation and the upper buttons.
BJ – Single ergonomic lever that makes the best use of the proportional 3 axis electronic control. The upper part of the joystick is equipped with a “ROLLER” (for the 3rd proportional axis) and simple buttons for further machine movements.
VSC – The screen on the front of the joystick allows instantaneous checking of the brushcutter movements and its most important data.

ON – OFF

Electric ON/OFF allows complete electrical control of the brushcutter using the Joystick on the console, allowing quick machine movements that can also be hydraulically regulated.

A Second Fixed Advanced Arm
APS Advanced Parallelogram System
ARC Machine with the ability to cut over obstacles
e Machine equipped with electric controls
EPG Proportional electric Load Sensing control EPP
EPP Proportional electric control EPP
K Reinforced brushcutter
Kit Magnum pumps Pumps high performance
MT Machine with side shift
Parallelogram System Ideal machine for cutting close to the tractor in confined areas
S Higher Horse Power Hydraulic System
S.I. System Electro-hydraulic float for the main arm
T Telescopic Second Arm
T Telescopic First and Second Arm
X Central rotation of the arms
Our Boom Mowers have the main arm pivot mounted on the centre
line of the tractor
Rollers
REAR ROLLER

As standard on all flailheads the rear roller can be manually adjusted to suit different applications.
When verge mowing the roller can be adjusted to change the cutting height. When hedge cutting it can be set higher to avoid coming in to contact with the hedge.

REAR ROLLER

Rear roller with double taper roller bearings, removable and resistant to axial forces. The rounded end of the roller ensures extreme resistance to contact with the kerbside, and with an outside diameter of 140mm roller becomes very sensitive to changes in the underlying soil.

CENTER OF GRAVITY

The axis of the plug coupling between rotor and 2nd arm of the brushcutter, is perfectly in line with the center of gravity of the rotor. This allows optimum control of the cutting head, an axial thrust is free of any kind of tensions with consequent reduction of load on pins and needles.

TRASMISSION REVERSED

The rotation of the rotor is guaranteed through 3 timing belts on 2 pulleys. This type of transmission, it guarantees shock absorption and the reduction in overall dimensions rotor.

EVO PLATE ATTACHMENT

For models M430X, the EVO cutting head with upper or rear attachment plate can be requested without a difference in price.